Linear rnachines with continuous preform motion: 1 to 12 cavities
Even heat distribution and easy operation
Rotary machines: 10 and 14 cavities
High output at a lower cost
Machine Features Linear Shuttle Machines
Gaylord tipper
Preform hopper
lncline conveyor
Unscrambler
Machine in - feed
Oven section
Blow clamp
Out - feed
PET-ALL Manufacturing
Machine Features continued
Preforms spin on mandrels
Preforms are heated with infrared lamps
Preforms are placed in blow molds as groups
(2,3,4, or 6)
Preforms are stretched and blown
Machine out - feed
1 Cavity Fully Automatic Shuttle Model TS1000
Excellent Price
Excellent Performance
Range of Linear Shuttle Machines
1 to 6 cavities
Most widely used machine type for small to medium sized applications
Outputs from 1,000 to 8,400 b/h with all - electric model
Neck sizes from 30 to 200 mm
Volumes from 50 ml to 5 gallons
Heat set, thread orientation, and preferential heating available on some models
Benefits and lssues of Linear Shuttle Machines
Shuttle means that the movement through the ovens is 'go - and stop'
+ Low capital investment
+ Easy setup
Preform heat Iess than continuous motion machines; to compensate Chumpower machines allow the adjustment of blow parameters for individual cavities
Spacing in ovens is the same as in blow mold - this is not as efficient as more air is heated up and escapes
Chumpower Acronyms
CPSB: Chumpower Stretch Blow
T: Standard
Number: Number of cavities times 1,000 (except in rotary and LS machines)
L: Large container
W: Wide Mouth
H: Heat - Set
H: Rotary
SS: Small Size (0.6 I maximum)
Wide Mouth Containers
One or two cavity machines available for diameters (mouth) up to 200 mm, standard
Wide mouth Jar Series / Automatic PET stretch blow molding machine
CPSB-1000L / 2000L
CPSB-1000W / 1000WM / 2000W
CPSB-2000LHI
CPSB can make :
Oval, Off center, Petaloid, Square, Flat, Round bottles, Jars and Wide mouth containers .....etc.
Market segment of CPSB :
Mineral water, Edible oil, Alcoholic drinks, CSD, Pickle food, Soda drinks, Cosmetics, Clean lotion, Detergent, Tennis bottles, PET bottles for cooking oil with handle
Features:
PET STRETCH BLOW MOLDING MACHINE
For Large volume, Oval & Flat Bottles, and Wide mouth Jar.
Compact structure for saving space; Modular design for easy maintenance.
Suitable for various markets to produce different bottles.
Special heating array structure to minimize oven space and energy consumption.
Optional:
PET bottle with Handle pre-insert robot.
Side-heating system for oval & flat bottles.
Smart locating device for specific direction of preform.
Output :
800-1600 bph
Cavities :
1 – 2
CONTINUOUS MOTION, ALL ELECTRIC, RHSB
New Brochure - Increase in Cavitation
LS 6000
This linear rnachine is different in several ways:
In - feed is like a rotary machine with star wheels:
proven concept with high reliability
Movement of preforms through the ovens is
continuous: even heat for all preforms
Spacing in ovens is fixed depending on model;
preforms are then spread to blow mold pitch: batter use
of ovens, energy savings
Servo motor clamp: fast and reliable
Design layout
Compact design
Space savings
Easy access
Easy maintenance
Infeed
Compact design
Space savings
Easy access
Easy maintenance
Heating section
Modular ovens with easy access
50 mm preform spacing for best energy usage
Preform are always right side up eliminating turn over problems, chain wear etc.
2 x 3 ovens layout with turnaround section for equalization of preform temperature
Oven Details
Chumpower lamp spacing is 17 mm {155mm on request)
Lamps can be moved
6 to 16 lamps per oven
Each lamp can be turned on or off
Heat shield is watercooled
Pitch Changing Unit
Preform transport and pitch unit are both controlled by servo motors
Pitch unit grabs preforms, then moves them towards blow clamp and enlarges the pitch to blowing dimension
Clamp Unit
Toggle clamp triggered by cam
Cam controlled by servo motor
Cam rotates continuously in one direction greatly reducing vibration
Patented design
Stretch rod is servo motor controlled
Each cavity has its own set of blow valves allowing individual control and reducing air consumption
Blow nozzle seals on transfer ring - no neck deformation
Bottom insert movement is mechanically coupled to clamp
Pressure compensation reduces bottle parting line and mold wear
* New: All speeds now increased from 1500 to 1700 parts/hour per cavity.
* CPSB LSS 12000 now available (12 cavity) at 20,000 + parts/hour. (0.61.)
Rotary Machines
CP offers a 10 - cavity machine at this time
There are 4 models:
CPSBR - 10 - 36: Max. neck 28 mm, oven pitch 38 mm
CPSBR - 10 - 50: Max neck 43 mm, oven pitch 50 mm
Both machines have a maximum output of 14,000 b/h
CPSBH - 10 - 38H; Same as above for heat - set
CPSBH - 10 - 50H: Same as above for heat - set
Heat set machine output is 10,000 b/h
Benefits of Rotary Machines
Every preform is exposed to the exact same amount
of heat and time between heating end blowing
Small oven pitch allows efficient heating
Synchronization is mechanical and, once set, very
repeatable
Low dead - volume of air means lower air consumption
In - feed end out - feed are both mechanical and not
prone to failure.
Pressure compensation means Iess stress on mold
Chain Pitch in Ovens
In indexing machines pitch of mandrels in the
ovens is the same as in blow mold "4"
Ovens are not loaded optimally
Large necks possible
In rotary and LS - 6000 machine pitch is either 38
or 50 mm
Energy savings due to better oven usage
Neck size limited by pitch: transfer ring must be 1.5
mm smaller than pitch
Compressors
Blow machines need 30 to 40 bar (420 to 580 psi) air pressure
Compressor is by far the most expensive ancillary equipment for stretch blow molding
PET All compressors use a Chinese supplier that came out of lngersoll - Rand as the best
compromise between low cost and reliability
These compressors are modular. Single unite of 20 to 40 cfm are stacked together to form larger systems that can easily be expanded
PET All presents high-quality reheat stretch blow molding machinery at lower production costs in Canada. We provide 3 types of machines to take care of all of your reheat stretch blow molding needs. Our world class machines and molds are being used at many manufacturing units for highly efficient and cost-saving production processes. Manufactured with the latest technologies and tested for perfection, our reheat stretch blow molding machinery can be installed in easy steps and provides complete solutions for production of plastic products. Our machines are designed to function continuously for long hours with minimal down time and with high rates of efficient manufacturing. We have provided the complete specifications of our reheat stretch blow molding machinery, so that you can select the model best suited for your requirements in Canada
I will recommend PetAll to anyone who want molding machine for their company. I have a plastic molding business, I wanted to expand my business so I wanted a new machine, so I called them for inquiring for new machine, they told me each and every specification of the latest machine and how does it works. They are really professional.
Daniel Lemont
I am very impressed with this company. I bought blow molding machines for my business. The equipments were affordable. I recommend this company to everyone in the plastic business.
Nicole Hepburn
We found Pet All team very supportive & accommodative. We contacted them for the Plastic Bottle Molding machine service which we found really helpful for our industry. We are thankful for their service.