www.petallmfg.com

Injection Blow Molding Machinery

Home » Product » Injection Blow Molding Machinery

Introduction: There are 4 choices of Can Mold Injection Blow Molding Machinery

This is the most popular range of Injection blow molding machine because all hydraulics are situated beneath the mold in the base of the machine. The Injection Blow Molding Machinery system is fool proof and does not allow oil from the hydraulics to contaminate the mold or the finished product. The machine has the added advantage of using a pull down tiebar system which is excellent for large cavitations used in the 135 Ton and 189 Ton range. The alternative is hydraulics above the mold where leaking may occur, thus contaminating the mold area. Furthermore, applying pressure more to the center of the mold than the pull down outside tiebars often inhibits the complete formation of the outer molds because of flexing. Large machines of the non-inverted head type, also are susceptible to frame cracking because of the flexing. A full range of machines is available > From 57 Ton to 189 Ton.

IBM Catalogue Inverted Head Can Mold Machines (Complete Program) Inverted Head Can Mold Inverted Head Can Mold

Not only are the injection blow molding machines available, but also Injection blow molding machine tooling is offered as a full technical service. The equipment that has been specially designed for Pet All Manufacturing Inc., and all machines for the Canadian market are tested and approved at our engineering centre before release to customers.

  • Model 250/450 (50 Ton)
  • Model 300/700 (78.6 Ton)
  • Model 700/1200 (135 Ton)
  • Model 700 / 1600 (189 Ton)

The Can Mold Inverted Head (upside down hydraulics) brand machines have the following outstanding features:

  • Heavy duty solid construction
  • Oil-free components in the sector above the take-off conveyor giving added suitability for use in pharmaceutical and delicate cosmetic containers
  • Screw and barrel composition: The screw is made of high quality 38 CrMoA1A material and is hard plated to 40Cr. The barrel is made of high quality bearing steel and is spray welded with hard alloy.
  • The machines come complete with all-round security guarding which is not shown in the photographs, and meet OSHA specifications.
  1. Oil Pump Vickers & Parker Denison (USA)
  2. Hydraulic valves Vickers (USA)
  3. Pneumatic valves Festo (Germany)
  4. Control computer Mitsubishi & Omron (Japan)
  5. Switch Omron (Japan)
  6. Transducers Gefran (Italy)
  7. Displays Allen Bradley (USA)
  8. Low-tension wiring Schneider (France)
  9. Oil motor Intermot (Italy)
  10. Electromotor Bijie (China)
  11. Mold temperature control Shini (China)
  12. Screw and barrel Jinyou (China)
  13. Working table Cast Iron
Product Sizing for Injection blow molding machine Bottles

Please see the chart below of Injection blow molding Machinery product sizing of bottles for each size of body/diameter etc. These are good estimates only.

Product Size IBM 250/450
60 Ton
IBM 300/700
88 Ton
IBM 700/1200
135 Ton
Volume Neck Dia Height Body Dia Cavities Cavities Cavities
5ml 10 35 15 14 22 30
10ml 12 40 20 12 20 30
20ml 15 50 25 10 18 28
30ml 20 60 30 9 16 26
40ml 22 65 35 8 14 24
60ml 28 75 40 8 13 22
80ml 30 80 45 7 12 20
100ml 32 85 50 6 12 20
150ml 35 90 53 5 10 18
200ml 38 100 58 4 8 16
400ml 42 120 65 3 6 12
650ml 50 160 80 2 5 10
1000ml 40 200 90 4 8
1500ml 45 200 103 3 6
Inverted Head Can Mold Injection blow molding products

The same range of machines is available in hybrid electric, with the screw being full electric and the main motor being servo assisted..

Full Electric Inverted Head Range

Available in the same range of machines as Injection blow molding machine Inverted Head above.

More than 30% energy saving and up to 15% faster cycle times than full hydraulic systems.

Low Pollution and no noise.

The fully electric is driven totally by B & R controller and B & R Servo Motors (all made in Austria).

Servo Motors (all models)
There are 10:

  • 1 on stripper (horizontal)
  • 1 on timer (vertical)
  • 2 on injection clamp
  • 2 on blow clamp
  • 3 on injection extruder recovery
  • 1 on transfer head (up-down)
Injection Blow Molding Machinery

The same range of machines is also available in full electric.

Hybrid Electric Inverted Head Range

Electric screw drive and servo assisted main motor.

More than 15% energy saving over full hydraulic systems.

Jomar and Uniloy have Hybrid - Electric at greatly inflated prices. Thruput is faster than the hydraulics, by 1-2 seconds. Prices are available on request, not that much more expensive.

Servo Motors (all models)
There are 3 :

  • 1 on extruder for injection and recovery assistance.
  • 1 on the clamp for assisting clamp tonnage.
  • 1 on discharge timer for horizontal movement.
Injection Blow Molding

These machines are generally lower cost and are available in a range up to 3 models 38 Ton, 60 Ton and 75 Ton. Hydraulics are above the head and the machines include an electronic gear box for accurate rotation.

Can Mold Nexion Injection blow molding Machinery Standard Hydraulic System

3 standard models are available in this range.

The Nexion is heavy duty, production proven over many years, and includes an electric gear box and B & R controls.

Data sheet - nexion IBM

Process: Injection Blow Molding

injection blow molding process chart

As an Injection Blow Molding Machinery manufacturer whose head office is located in Canada, the majority of our work is in IBM, where "Pet All" and "Can Mold" trademarks have established an excellent reputation.



Request a Quote